How to Connect The Braided Hose to Copper Pipe, Faucet And Toilets
You are here: Home » News » How to Connect The Braided Hose to Copper Pipe, Faucet And Toilets

CONTACT US

Tel: 86-574-27729177
Fax:86-574-27729100
Cell:86-18667830020
Add: RM804,NO.33 Lane 207 Huancheng Road (W)Ningbo, China.

Get a Quote

How to Connect The Braided Hose to Copper Pipe, Faucet And Toilets

Views:61     Author:Site Editor     Publish Time: 2020-11-06      Origin:Site

Things You'll Need


  • Dielectric union

  • Extension tubing

  • Pipe wrench


Copper pipe is commonly used for under-sink water supply lines both in the kitchen and in the bathroom. However, most sinks on the market are equipped with flexible stainless steel hoses that drop down from beneath the faucet assembly. The most common way to connect the stainless steel hose to the flexible copper pipe is with a dielectric union and a plastic piece of extension tubing or a coupling.


How to Connect The Braided Hose to Copper Pipe, Faucet And Toilets


Step 1

Turn off the main water supply under the sink by turning the water control valve fully to the left.


Step 2

Remove any hoses or tubing attached to the copper water supply line with the pipe wrench.


Step 3

Screw one side of the dielectric union onto the threaded end of the copper pipe.


Step 4

Stretch the stainless steel water line from the bottom of the faucet connection to see if it reaches the dielectric union attached to the copper pipe. If so, connect the end of the stainless steel braided hose directly to the dielectric union and tighten with a pipe wrench.


Step 5

Connect one end of the extension tubing directly to the dielectric union if the flexible line coming from the sink is not long enough to reach. Connect the other end of the flexible tubing to the braided stainless steel hose. Tighten the connections with the pipe wrench.


Replacing A Faucet


New sink faucets typically install easily, thanks to flexible water supply hoses that connect the copper water supply pipe to the fixture. These hoses are reinforced with braided stainless steel mesh and have threaded connections at both ends. Connecting the faucet to your home's supply hose is as simple as screwing the two hoses together and tightening them with a small adjustable wrench. If you already have this flexible hose set up in your bathroom, then upgrading your faucets will take less than half an hour. If you have an old copper-pipe installation, then the job may take several hours.


If your house is more than a couple of decades old, you probably have solid copper water supply pipes that connect directly to your faucets. In the past, changing a faucet in this situation required precisely cutting and soldering the copper pipe and faucet together, but now all that has changed. If the faucet you're replacing is connected directly to copper pipes, then you won't even have to unsolder it to remove the old fixture. Instead, just shut off the water supply valve, cut the copper pipes with an inexpensive pipe cutter so at least several inches of copper pipe extend from the floor or wall, then lift out the old faucet.


Now hook up some flexible supply lines. The best way to connect a flexible supply line to copper piping is by installing a shut-off valve that includes a threaded compression joint. One end of this valve is threaded to accept the flexible water supply hose that connects to the faucet, and the other end slips over the end of a half-inch copper pipe and tightens with a compression ring. Simply slide the threaded compression nut onto the copper supply pipe, then slip on the compression ring. It’s a brass ring with tapered edges, which barely fits around the outside of the half-inch copper pipe. Push the valve body onto the end of the supply line, slide the ring up to it and tighten the compression nut. When you tighten the nut, the thin edges of the ring squeeze against the outside surface of the pipe, sealing it without solder.

 

Replacing A Toilet


Most weekend DIYers will have no trouble changing out a toilet, provided they are savvy to a couple of installation tricks. It’ll take just a few hours and a few wrenches to get the job done.

Start by shutting off the water supply valve to your existing toilet. Remove the water from the tank and bowl by flushing to expel most of the water, and then soak up the rest with a sponge. The drier you can get the tank and bowl the better.


Yowin is a professional manufacturer and supplier of stainless steel corrugated hosesSS braided hosesbraided gas hose and stainless steel shower hose, etc. Contact us for more details.


Navigation

Contact Us

 Tel: +86-574-27729177
 Email:sales@yowinpipe.com
 Fax:+86-574-27729100
 Cell:+86-18667830020
 Add: RM804,NO.33 Lane 207 Huancheng Road(W)Ningbo, China.
Copyright © 2019 Ningbo Yowin Pipe Industry Co.,Ltd. All Rights Reserved. XML |Sitemap